




12 V | 16-tooth steel pinion | counter-clockwise (CCW) | PMDD permanent-magnet direct drive
Pinion: 16 teeth, outer diameter 32.5 mm (1.280 in), steel
Shaft diameter: 10.1 mm (0.398 in)
Mounting holes: multi-hole flange, 6.7 mm plain holes (unthreaded, 3-4 holes), bolts through with nuts
Housing length: field case 93.2 mm (3.67 in)
Electrical connection: single B+ main power stud, housing as earth ground
Compatible Engines: Tecumseh horizontal L-head singles HM70 / HM80 / HM85 / HM90 / HM100, OHM90 / OHM100 / OHM120, OVM120, OVXL120, TVM125 / TVM140 / TVM170 / TVM195 / TVM220, TVXL220; Tecumseh OE numbers 29965 / 32468 / 33605 / 35763 / 35765 / 36463 / 36680 series (1966-1983)
Compatible Models: John Deere 56 (1971-1974), 57 (1971-1974), 60 (1966-1969), 65 (1978-1983), 66 (1975-1977), 70 (1970-1974) riding mowers; some Cub Cadet snow blower fitments
Replaces: John Deere AM32092 / AM30931 / AM34731; Tecumseh 29965, 32468, 32468A, 32468B, 33605, 33606, 35763, 35763A, 35765, 35765A, 36463, 36680; Lester 5752 / 5752N; Arrowhead STC0007; DB Electrical 410-22000 / 410-22007; JANNCO 410-22000R; Atlantic Quality Parts 1400-0177; Rotary 106-306
12-volt permanent-magnet direct-drive starter for the Tecumseh-powered vintage John Deere riders. The 16-tooth steel pinion and short 93.2 mm field case match the old-pattern flywheel ring gear exactly, and the 6.7 mm plain-hole flange bolts straight onto the original block - no drilling, no adapters. It is the replacement that keeps a 1966-1983 John Deere starting like it did the day it left the showroom.
This unit serves the vintage-economy segment: John Deere 56 through 70 riders that are still working gardens and small properties more than forty years after they were built. Because the same physical starter carries both the John Deere numbers and twelve Tecumseh numbers, one SKU answers enquiries from two different buyer groups - tractor owners searching AM32092 and small-engine owners searching 32468 or 35765. Few suppliers list this old-pattern starter at all, so stockists face almost no local competition while serving a fleet that cannot be replaced.
Permanent magnets in the field housing do the work that old wound field coils did, so more of the battery current reaches the armature and less is wasted as heat in the windings - that is why this compact PMDD unit spins a cold Tecumseh single that a tired original struggles to turn.16-tooth pinion sits on a Bendix-style inertia drive: as the armature accelerates, the pinion screws forward along the shaft thread into the ring gear; once the engine fires, the flywheel outruns the pinion and throws it back clear, so the gear cannot be held against a running engine. The steel gear teeth and hardened sleeve are sized for that daily hammer-in engagement without peening.
The windings are pure copper for low resistance and cool running, and the brushes are sized for hundreds of cold starts rather than a single season. The drive-end housing is sealed against grass dust, rain splash and wash-down water - the two failures that kill field starters are commutator contamination and gear tooth wear, and both are addressed here. They can finish resists fertilizer and rain corrosion, so the starter survives a season mounted next to a spreader or stored in a damp barn, conditions most vintage JD riders see every year.
Typical failures this part replaces: a clicking sound with no crank (worn brushes or a burned armature), a grinding engagement noise (stripped or missing pinion teeth), and a starter that spins but will not turn the engine (slipped inertia drive). On these older riders the original starter has usually been rewound once or twice already, and a second rewind is rarely cheaper or more reliable than this tested new unit. One caution worth passing to buyers: this is the 16-tooth / 32.5 mm old-pattern unit with 6.7 mm plain holes - it sits beside, but does not replace, the later 14-tooth 5937 family, so counting teeth and checking the mounting holes before purchase prevents most returns.
For a repair shop, a bolt-in tested starter turns a no-start vintage John Deere into a same-day fix with no machining, no rewinding and no waiting on a rebuild house. For a distributor, the AM32092 / 5752 / STC0007 / 410-22000 cross-reference set matches what Lester, Arrowhead and DB Electrical already publish, so the listing appears in the searches buyers are already running on both the JD and Tecumseh sides. MOQ 50 with a 7-30 day lead time and 12-month warranty keeps the economics straightforward for the shelf.
| Brand | Model | Model Code | Year |
|---|---|---|---|
| Tecumseh | Tecumseh Horizontal Single (HM70-HM100, 281-333cc, 7-10 HP) | TEC-HM-SERIES | 1966–1983 |