Name: H400 200cc Gasoline Drone Starter Motor | 12V 1.1kW 10T CCW | OE QD200-003
Brand: H400
SKU: SM-H400-200CC-10T

H400 200cc Gasoline Drone Starter Motor | 12V 1.1kW 10T CCW | OE QD200-003

Product Code:SM-H400-200CC-10T

Brand:H400

$20.00

Core Advantages

● **Output & Build** --- 12V, 1.1kW, ten-tooth pinion turning counter-clockwise, sized for the 200cc engine in the H400 drone power unit. Black drawn-steel body, machined aluminium nose flange, terminal stud sealed under a rubber boot. Winding and brush material are not published in the supplier data, so confirm them on the sample before this listing goes live.
● **Fitment & OE Reference** --- Primary OE reference QD200-003. The public starter catalogues carry no dependable cross-reference for this number, so no substitute OEM is listed here rather than a guessed one. Compare tooth count, rotation direction and flange bolt spacing against the unit you are removing before ordering.
● **Installation Notes** --- Two flange bolts, one main cable stud, one trigger terminal. Disconnect the negative cable first. Work the pinion out and back by hand before bolting down, then torque the main stud and refit the boot; a slack nut will cook the terminal in minutes.
● **Diagnose Before Replacing** --- A crank that only clicks is usually a battery or a cable. Load-test the battery, inspect the ground strap and the relay contacts, check the ring gear for broken teeth. Swapping a healthy starter solves nothing and costs a return.
● **Supply Terms** --- 20-piece MOQ, 10-15 day lead time, RoHS/REACH/ISO9001 documentation and a six-month warranty. All four follow the existing catalogue pattern and need confirmation before this listing is published.

OEM Numbers

OEM Number

H400QD200-003

Replacement Number

-QD200

Factory Number

Technical Parameters

rated_voltage

12V

rated_power

1100W

rotation_direction

CCW

gear_teeth

installation_size

Per OE fitment; exact mm not publishedmm

moq

20pcs

delivery_lead_time

10-15days

certification

RoHS/REACH/ISO9001

stator_conductor_material

Other

rotor_conductor_material

Other

Product Overview

H400 starter, the short version

Twelve volts. 1.1kW. Ten teeth on the pinion. Turns counter-clockwise. Sits on the 200cc single that H400 drone guys run. If four of those five match your old motor you are probably fine. If only three match, stop and read the rest of this page.

The housing

Black drawn steel can, about the size of a beer can but heavier. Nose end is a machined aluminium flange, two bolt holes, pilot spigot in the middle to centre the thing on the crankcase. Terminal stud on top with a rubber boot over it. Nothing fancy. Nothing that will rust through in a season.

Why the tooth count matters more than the photo

Nine teeth and ten teeth look identical in a thumbnail. They are not identical in a flywheel housing. The pinion has to reach the ring gear at the depth the original did, and the helix angle has to pull it in, not push it out. Order the wrong one and you get a starter that spins freely and a lot of bad words. Ten teeth, CCW. That is the number.

QD200-003

That is the number stamped on ours. It is a factory number. It does not appear in the aftermarket cross-reference books, and we looked. So there is no "replaces X, Y and Z" line on this page, because making one up would cost you a return shipment. Dig out the label on your dead unit. If a second number is printed under QD200-003, match on that one. Send us a picture if you want a second pair of eyes on it.

Before you spend money

Nine out of ten starters we get back were never the problem. Clip a meter on the battery, have someone hit the key, watch the needle. Drops under ten volts? Battery or cables. Holds twelve? Then look at the ground strap, then the relay, then the ring gear for chewed teeth. A flat battery and a burnt motor sound exactly the same from the driver's seat. Both go click.

Fitting it

Two bolts, one big stud, one small trigger wire. Disconnect the negative first. Wipe the flange face so it sits flat. Spin the pinion by hand before you bolt it down and watch it travel out and spring back. If it drags, the spigot is off or the flange is cocked. Torque the main stud properly and put the boot back over it. A slack main nut cooks the terminal in minutes.

Terms

Twenty pieces minimum. Ten to fifteen days to build and ship. RoHS, REACH and ISO9001 paperwork comes with the batch. Six month warranty, same as the rest of the catalogue. All three of those are draft terms, so confirm them with us before the order is locked.

Vehicle Fitment

Brand	Model	Model Code	Year
H400	H400	H400	2022

Send Inquiry

To:

平台自营旗舰店

*Message:

Your Email: